Go to Parker.com
Search
Sign in
Technologies
Aerospace
Climate Control
Electromechanical Group
Filtration
Fluid and Gas Handling
Hydraulics
IoT
Pneumatics
Process Control
Sealing and Shielding
Blogs
Forums
Knowledge Bases
Parker Community
Technologies
Aerospace
Climate Control
Electromechanical Group
Filtration
Fluid and Gas Handling
Hydraulics
IoT
Pneumatics
Process Control
Sealing and Shielding
Blogs
Forums
Knowledge Bases
Search
User
Site
Search
User
Home
Technologies
Electromechanical Group
Electromechanical - Industrial
Electromechanical Industrial Knowledge Base
TCP/IP Ethernet and a Dial-Up Connection
Technologies
Electromechanical Group
Electromechanical - Industrial
More
Cancel
Electromechanical - Industrial
Electromechanical Industrial Knowledge Base
TCP/IP Ethernet and a Dial-Up Connection
Electromechanical – Industrial Support Forum
Electromechanical Industrial Knowledge Base
Members
Sub Groups
More
Cancel
New
Electromechanical - Industrial requires membership for participation - click to join
Electromechanical Knowledge Base & Frequently Asked Questions
+
Motion and Machine Controllers
+
General Technology Information
+
Virtual Engineer
-
Visualization and Human Machine Interface (HMI)
-
Interact (Legacy)
Replace/Upgrade Interact panel P11/P1H/P15/P2/P3/P4/P5 etc
CTC and i-Motors
Configure a TCP/IP Dial-Up Adapter Connection.
Interact Misc - Can ASCII register in the PLC be used as an alarm?
Configure a TCP/IP connection (IP address)
Compact Flash Disk Transfer using Interact MachineShop Toolbar to Upload and Download
ERROR - Invalid Panel list or Key Pad Address.
Ethernet download to a CTC Panel.
How to Restore Motion Panel.
Interact Software - Display alarms in a RMD tool within PTM
How to run app on my PowerStation on boot-up?
Implementing the New CMOT Driver
LEDs on the back of the Profibus card
MachineLogic - How do I clear Retentive Memory?
MachineLogic - No project on the PLC.
Security Key Setup not Installed
Single layer SST 5136-PFB-104 card with Interact.
TCP/IP Ethernet and a Dial-Up Connection
TCP/IP open port failure
Can I run Interact 6.X in Windows NT/2K/XP?
Can I run Interact7 on my Windows 10 or 7 PC?
Configure a TCP/IP connection (DHCP)
Configure a TCP/IP direct Ethernet connection
CTC Runtime Data Error Symbols (! ? broken pencil etc)
Enable/disable the screen saver
Flashback Utilities for the CTC DOS Based PowerStations - If you have Interact ver 7 it installs all the necessary Flashbacks.
HMI Battery Replacements
How do I connect my P13, PA or PA2 Interact HMI to DataHighway Plus Network?
How do I recalibrate my Interact touchscreen? Or change the panel's ethernet address?
How do I show hidden and protected files in Windows?
How do I transfer my old Interact application to a newer Interact panel?
How to connect my device to Interact? Interact Cable Dictionary
How to print graphics from Interact run mode.
I upgraded my old hardware to a PA2 and have Vertical Stripes on screen and does not load my application.
Interact does not recognize the security key.
Interact: Error Initializing AMM - Invalid Logging Path
Minimum of NT 4.0 SP3 to install Machine Shop
Powerstation Shell on older CTC units
Replacing old HMIs that run Interact
Upgrading from a PA to a PA2
What are Interact Runtime modules?
Whats the difference between FLH-0512P and FLH-0512?
What internal variable can I use to R/W ASCII?
Interact Troubleshooting - WinXP- cannot select options on Toolbar
Control Access to Panels and Tools using the Password User Levels in Interact
Driver for my Allen Bradley Micrologix 1500 PLC?
Fonts and Graphics on Tools broken after Interact Upgrade to Ver 7 to run on PA2 hardware. Application runs but FONT Size or images are wrong.
GESNP / GESNPX 9030 / 9070 Serial Com configuration for Interact / PowerStation PA/PA2/P13 etc...
I need more fonts for my Interact application.
INTERACT How to Order
Interact screen size too BIG or too small after upgrade. Only see part of screen or screen compressed in top left corner of display.
Legacy Product Page - P1 Series
Legacy Product Page - P2 Series
Legacy Product Page - P3, P4, P5 and P7 Series
PowerStation Accessories - Mounting kits, Connectors, Protective Overlays
Security Key not found or Not programmed to support Module or Driver
Which HMI runs Interact?
+
InteractX
+
Interact Xpress
+
IXA / PCA
+
IPX / IPC (Discontinued)
+
PHM / PM1 Industrial Monitors (Discontinued)
+
PA / PS / P1-P9 (Discontinued)
+
PX / HPX InteractX HMIs (Discontinued)
CE Declaration of Conformity for HMI
CTC/HMI: Connector Part Numbers
What CF Card do I need? And my HMI will not boot. Says no boot device found even after running the Flashback utility for my HMI model
Latest versions of HMI software packages
+
PFD - Parker Factory Display (Discontinued)
What HMI software runs on which models of HMI? (Consolidated History of HMI and Software Versions)
What software is on my Parker/CTC HMIs?
+
Servo Drives and Servo Drive/Controllers
+
Stepper Drives and Stepper Drive/Controller
+
AC/DC Industrial Drives
+
Gearheads
+
Servo Motors
+
Step Motors
+
Linear and Rotary Positioners
+
Electric Cylinders
+
T-Slot Aluminum Framing
+
C3 + Xpress + ETH
How can I stay updated on Parker electromechanical and drives product news?
+
Legacy (Discontinued)
+
Other
Memorandum: Information on EPA ban of Persistent bioaccumulative toxin (PBT)
TCP/IP Ethernet and a Dial-Up Connection
Revision
Creation Date
Revision Author
Select All
Current Revision
14 Dec 2017 6:42 PM
William Chin
4
Revision #4
12 Dec 2017 7:31 PM
Dean Moody
2
Revision #2
4 Oct 2017 12:54 AM
Former Member
1
Revision #1
1 Oct 2017 9:21 AM
Electromechanical and Drives Team
Compare Versions
View current version
